- 您现在的位置：买卖IC网 > Sheet目录1316 > 3-1470213-6 (TE Connectivity)CONN HEADER 36POS DL 2MM T/H 8AU
108-57197
NO.
TEST ITEMS
REQUIREMENTS
PROCEDURES
ENVIRONMENTAL REQUIREMENTS
3.5.4.1
Vibration
No electrical discontinuity greater
than 1 microsecond.
Subject mated connectors to 10-55-10 Hz
traversed in 1minutes at 1.52mm amplitude 2
Hours each of 3 mutually perpendicular
planes.
MIL-STD-202, Method201, Condition A
3.5.4.2
Temperature Life
(Heat Aging)
Termination resistance (low level)
shall be met.
Subject mated connector assemblies to
temperature life at 85°C±2°C for 96 hours.
Termination resistance 40m
ohms Max.
3.5.4.3
Humidity, Steady
State
Insulation Resistance (Final)
500M ohms min.
Termination resistance (low level)
Subject mated connectors to steady state
humidity at 40°C±2°C and 90-95% R.H for 96
hrs.
shall be met.
3.5.4.4
Thermal Shock
Termination resistance (low level)
shall be met.
Subject mated connector assemblies on 5
cycle –55 °C and +80°C for 30 minutes each
duration at temperature extremes.
MIL-STD-202, Method 107, Condition A
3.5.4.5
Resistance to
Soldering Heat
No Physical damage
Subject connector mounted on printed circuit
boards to solder bath at 260 ± 5 ° C for 5 ± 1
seconds (Flow soldering).
MIL-STD-202, Method 210, Condition C.
3.5.4.6
Durability (Repeated
Mate /Unmating)
Termination resistance (low level)
shall be met.
Subject connector assembly to 50 cycles of
repeated mating /unmating at a rate of 10
cycles a minute.
3.5.4.7
Salt Spray
30m Ω Max. (Final)
Exposing in a heat chamber at a temperature
of 35°C ± 2°C for 24 hours.
EIA-364-26A, CONDIION A.
Resistance to Wave
Soldering Heat
Resistance to Wave
Soldering Heat
Resistance to Wave
Soldering Heat
Resistance to
No physical damage shall occur.
No physical damage shall occur.
No physical damage shall occur.
Solder Temp. : 240 ± 5 ℃ , 10 ± 0.5sec.
Tyco spec. 109-202, Condition A
Solder Temp. : 265 ± 5 ℃ , 10 ± 0.5sec.
Tyco spec. 109-202, Condition B
Solder Temp. : 260 ± 5 ℃ , 10 ± 0.5sec.
Tyco spec. 109-202, Condition C
Pre-soak condition, 85 ℃ /85 ﹪ RH for 168
hours.
Pre Heat: 150~180 ℃ , 90 ± 30sec.
3.4.5.8
Reflow Soldering
Heat
No physical damage shall occur.
Heat: 230 ℃ Min., 30 ± 10sec.
Peak Temp. : 245+0/-5 ℃ , 10~30sec.
Duration: 3 cycles
Tyco spec. 109-201, Condition A
Pre-soak condition, 85 ℃ /85 ﹪ RH for 168
hours.
Resistance to
Pre Heat: 150~180 ℃ , 90 ± 30sec.
Reflow Soldering
Heat
No physical damage shall occur.
Heat: 230 ℃ Min., 30 ± 10sec.
Peak Temp. : 260+0/-5 ℃ , 20~40sec.
Duration: 3 cycles
Tyco spec. 109-201, Condition B
Figure 1
Rev
B
3 of 5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
3-1478985-0
CONN PLUG SMA DUST CAP W/CHAIN
3-1478986-0
CONN SMA JACK CAP W/CHAIN
3-1489841-3
CONN MEMORY SCKT 240P 400TL 15AU
3-1532006-0
CONN PLUG SOS/LEPRA STR 50 OHM
3-1546099-0
CONN BARRIER BLOCK 30CIRC 6.35MM
3-1546119-9
TERM BLOCK 22CIRC VERT .250
3-1546159-9
CONN BARRIER BLOCK 24CIRC 9.53MM
3-1546307-0
CONN BARRIER BLOCK 30CIRC 9.53MM
相关代理商/技术参数
3-1470213-8
制造商:TE Connectivity 功能描述:CONN UNSHRD HDR HDR 38 POS 2MM SLDR ST TH - Bulk
3-1470226-0
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 30 POS 2MM SLDR ST SMD - Tape and Reel
3-1470226-2
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 32 POS 2MM SLDR ST SMD - Tape and Reel
3-1470226-6
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 36 POS 2MM SLDR ST SMD - Tape and Reel
3-1470226-8
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 38 POS 2MM SLDR ST SMD - Tape and Reel
3-1470250-3
制造商:TE CONNECTIVITY 功能描述:
3-1470252-0
制造商:TE Connectivity 功能描述:1.0MM FPC SMT R/A TOP 30P - Tape and Reel
3-1470260-0
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 30 POS 2MM SLDR RA TH - Rail/Tube